Technical characteristics

Most running sizes advertising dynamically set (ADS) type "prizmatron" (TU 74.4-31199078-001:2006) advertising demo plane - (3x6) m and (3x12) m.
Indicator - Features Value of the index or the presence of characteristics
(3х6)m (3х12)m
1. Overall dimension (HxL) (3280х6361) mm (3280х12430) mm
2. Unit weight 550 kg. 1100 kg.
3. Number prism assembly (triangular core-tube assembly with three removable plates, fins) 56/58 pcs. 112/116 pcs.
4. Number of removable plates (lamellae) on each prism 3 pcs. 3 pcs.
5. Number of removable slats, just 168/174 pcs. 336/348 pcs.
6. Slat width 100 mm. 100 mm.
7. The gap between the prisms (5-7) mm. (5-7) mm.
8. Location prisms - vertical + +
9.Rotation prisms undulating
- From the left side to the right
- From the right to the left
- From the center to the edges
- From the edges to the center		  
+
+
-
-		  
-
-
+
+
10. Exposure time one plane
- recommended
- range		  
(7-14) seconds
1 seconds- 24 hr		  
(7-14) seconds
1 seconds- 24 hr
11. Time shift exposures (4–5) seconds (4–5) seconds
12. Rated voltage (+/- 15%) 220 V 220 V
13. Maximum power consumption of the motor 25 Vt 35 Vt
14.Maximum power consumption charger with combined power supply 100 Vt 100 Vt
15. The location of the engine assembly with gear
- At the bottom of the right side frame (typical variant)
- In the bottom left side of the rack (optional)
- Under the middle of the lower box body		  
+
+
-		  
-
-
+
16. Number of chargers with combined power supply 1 2
17. Number of batteries recommended capacity 90 A / h 1 2
18. Maximum voltage commutator motor 24 V 24 V
19. Maximum power consumption 0,15 kilowatt hour per day 0,25 kilowatt hour per day
20. Planetary gearbox + +
21. Motor, gearbox (geared motor) made in Germany + +
22. Degree of protection and automatic charger (controller) - IP 65 + +
23.Options box lids on buildings RDU
- flat
- Curly (convex)		  
+
+		  
+
+
24. Materials used
- Parts of the housing cap - rolled aluminum coated "anoxia"
- Tubes, fins, shaft - rolled aluminum
- Drive parts – Polyamide PA-610, Alloy Steel
- Details of fastening slat - polyamide PA-610
- Bevel gears on the shaft and gear - Alloy Steel		  
+
-
+
+
-
+		  
+
-
+
+
+
+


Main technical characteristics of the charger

Indicator - Features Value of the index or the presence of characteristics
1.Input voltage (+/- 15%) 220 V
2.Network frequency (50-60) Hz
3.Maximum power consumption 100 Vt
4.Maximum charge current 10А
5.Maximum charge voltage 16,5 V
6.While a full charge battery (battery) 90 A / hr 24 hr
7.Battery charging time (battery) 90 A / h for ADS within (12-18) hours (depending on the quality of the battery, mains voltage) (5-8) hr
8.Maximum battery capacity 120 А/hr
9.Recommended battery capacity 90 А/hr
10.Reverse polarity protection for battery +
11.Short-circuit protection (humidity) +
12.Surge protection (fuse) +
13.The ability to charge the battery after the battery is fully discharged +
14.Dosage according to the current level of battery charge +
15.Mechanical off when fully charged battery +
16.The presence of heat (increased headroom force elements) +
17.Separated from the power electronics malotochnoy (this increased level of security) +
18.Performance power components on wires +
19.Availability display for ease of use +
20.Superimposed corrugated protective tubes on the power wires (reduced probability of breakdown) +
21.Stand 3 x-fold loading (critical - 16A), then switches itself off and protection trips) +